Danfoss VLT HVAC Basic Drive FC 101 Technické informace Strana 18
- Strana / 99
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Closed Loop Set-up Wizard
No & Name Range Default Function
0-03 Regional Settings
[0] International
[1] US
0
1-20 Motor Power
0.09-110kW Size related Enter motor power from nameplate data
1-22 Motor Voltage
50.0 - 1000.0V Size related Enter motor voltage from nameplate data
1-23 Motor Frequency
20.0 - 400.0Hz Size related Enter motor frequency from nameplate data
1-24 Motor Current
0.01 - 10000.00A Size related Enter motor current from nameplate data
1-25 Motor Nominal Speed
100.0 - 9999.0RPM Size related Enter motor nominal speed from nameplate data
4-12 Motor Speed Low Limit [Hz]
0.0 - 400Hz 0.0Hz Enter the minimum limit for low speed
4-14 Motor Speed High Limit [Hz]
0 - 400Hz 65Hz Enter the maximum limit for high speed
3-41 Ramp 1 Ramp up Time
0.05 - 3600.0 s Size related Ramp up time from 0 to rated motor frequency par. 1-23
3-42 Ramp 1 Ramp Down Time
0.05 - 3600.0 s Size related
Ramp down time from rated1-23 Motor Frequency to 0
1-73 Flying Start
[0] Disabled
[1] Enabled
0 Select Enable to enable the frequency converter to catch a
spinning motor
3-02 Minimum Reference
-4999-4999 0 The minimum reference is the lowest value obtainable by
summing all references
3-03 Maximum Reference
-4999-4999 50 The maximum reference is the highest value obtainable by
summing all references
3-10 Preset Reference
-100-100% 0 Enter the set point
6-19 Terminal 53 mode
[0] Current
[1] Voltage
1 Select if terminal 53 is used for current- or voltage input
6-10 Terminal 53 Low Voltage
0-10V 0.07V Enter the voltage that corresponds to the low reference value
6-11 Terminal 53 High Voltage
0-10V 10V Enter the voltage that corresponds to the low high reference
value
6-12 Terminal 53 Low Current
0-20mA 4 Enter the current that corresponds to the high reference value
6-13 Terminal 53 High Current
0-20mA 20 Enter the current that corresponds to the high reference value
6-14 Terminal 53 Low Ref./Feedb.
Value
-4999-4999 0 Enter the feedback value that corresponds to the voltage or
current set in par. 6-10/6-12
6-15 Terminal 53 High Ref./Feedb.
Value
-4999-4999 50 Enter the feedback value that corresponds to the voltage or
current set in par. 6-11/6-13
6-16 Terminal 53 Filter Time
Constant
0-10 s 0.01 Enter the filter time comstant
20-81 PI Normal/ Inverse Control
[0] Normal
[1] Inverse
0
Select Normal [0] to set the process control to increase the output
speed when the process error is positive. Select Inverse [1] to
reduce the output speed.
20-83 PI Start Speed [Hz]
0-200Hz 0 Enter the motor speed to be attained as a start signal for
commencement of PI control
20-93 PI Proportional Gain
0-10 0.01 Enter the process controller proportional gain. Quick control is
obtained at high amplification. However if amplification os too
great, the process may become unstable
1-29 Automatic Motor Adaption
(AMA)
See 1-29 Automatic Motor
Adaption (AMA)
Off Performing an AMA optimizes motor performance
How to Programme VLT HVAC Basic Drive Programming Guide
MG.18.B1.02 - VLT
®
is a registered Danfoss trademark 17
2 2
- Programming Guide 1
- 1 Introduction 2
- 3 Parameters 2
- Contents 2
- 2 MG.18.B1.02 - VLT 3
- 4 Troubleshooting 4
- 5 Parameter Lists 4
- 4 MG.18.B1.02 - VLT 5
- 1.1.2 Symbols 7
- 1.1.3 Abbreviations 7
- Definitions 8
- 175ZA078.10 9
- Pull-out 9
- MG.18.B1.02 - VLT 10
- High Voltage 11
- 1.1.6 Electrical Overview 12
- 2 How to Programme 13
- 14 MG.18.B1.02 - VLT 15
- Closed Loop Set-up Wizard 17
- Main Menu 19
- * English 21
- * Interna 21
- * Active Set 22
- 3.1.3 0-3* LCP Custom Readout 23
- 3.1.4 0-4* LCP 24
- 3.1.5 0-5* Copy / Save 24
- 3.1.6 0-6* Password 24
- * Variable 25
- * [0.01 - 26.0 26
- * [100.0 26
- * Off No function 26
- 3.2.3 1-3* Adv. Motor Data 27
- 1-4* Cable Length 27
- 3.2.7 1-7* Start Adjustments 28
- 3.2.8 1-8* Stop Adjustments 29
- 3.2.9 1-9* Motor Temperature 29
- 3.4.1 3-0* Reference Limits 31
- 3.4.2 3-1* References 31
- * Analog in 54 32
- * Local bus 32
- * [0.05 32
- 3.4.5 3-8* Other Ramps 33
- 3.5.1 4-1* Motor Limits 34
- 3.5.2 4-5* Adj. Warnings 34
- 3.5.3 4-6* Speed Bypass 35
- 3.6.1 5-0* Digital I/O Mode 36
- 3.6.2 5-1* Digital Inputs 36
- * No operation 38
- * Coast inverse 38
- 3.6.3 5-4* Relays 39
- 5-40 Function Relay 40
- Option: Function: 40
- 3.6.4 5-9* Bus Controlled 41
- 3.7.1 6-0* Analog I/O Mode 42
- 3.7.2 6-1* Analog Input 53 42
- 3.7.3 6-2* Analog Input 54 43
- * [0.0 - 200.0 44
- * [0.0 - 100.0 %] 44
- * 0-20 mA 45
- Options - Group 8 47
- 3.8.1 8-0* General Settings 47
- 3.8.2 8-3* FC Port Settings 47
- 3.8.3 8-5* Digital/Bus 48
- 3.8.4 8-7* BACnet 49
- 3.8.6 8-9* Bus Feedback 50
- 3.9.1 13-** Prog. Features 51
- 13-0* SLC Settings 51
- * Do not reset 53
- * Disabled 53
- * [-9999.0 54
- * [0.0 54
- 13-52 SL Controller Action 58
- * Manual reset 59
- 3.10.4 14-4*Energy Optimising 60
- 3.10.5 14-5* Environment 60
- * [1.0 - 16.0 kHz] 61
- 3.11.1 15-0* Operating Data 62
- 3.11.2 15-3* Alarm Log 62
- 3.12.1 16-0* General Status 64
- 3.12.2 16-1* Motor Status 64
- 3.12.3 16-3* Drive Status 65
- * [0.1 - 9999.0 69
- * [0.0 - 400.0 %] 69
- * [0.0 - 400.0 Hz] 70
- * [0.0 - 100.0 70
- Group 24 72
- 3.16.1 24-0* Fire Mode 72
- Range: Function: 74
- 4.1.1 Alarm Words 77
- 4.1.2 Warning Words 77
- 4.1.3 Extended Status Words 78
- 4.1.4 Fault Messages 78
- 78 MG.18.B1.02 - VLT 79
- 5.1.3 1-** Load and Motor 83
- 5.1.4 2-** Brakes 84
- 5.1.5 3-** Reference/Ramps 84
- 5.1.6 4-** Limits/Warnings 85
- 5.1.7 5-** Digital In/Out 85
- 5.1.8 6-** Analog In/Out 86
- 5.1.9 8-** Comm. and Options 87
- 5.1.10 13-** Smart Logic 88
- 5.1.13 16-** Data Readouts 90
- 5.1.16 22-** Appl. Functions 91
- 92 MG.18.B1.02 - VLT 93
- 94 MG.18.B1.02 - VLT 95
- 96 MG.18.B1.02 - VLT 97
- *MG18B102* 98
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce