Danfoss TP7000 Uživatelský manuál stáhnout pdf (Strana 2)

Datasheet

Part No. 560v08 03/08

TP7000 Series - Programmable Room Thermostats

Installer Settings -

Optimum Start Control

If DIL SW2 has been set to Optimum start control

enabled, the Optimum start control setting must

be made within the user programming mode. The

table below shows the calculated time before the

programmed time that the ﬁ rst event of the day will

commence, dependant upon the difference in room

temperature and the programmed temperature for the

ﬁ rst event. Setting options are 0:00, (OSC disabled,

0:30, 1:00, 1:30 or 2:00).

Desired Event 1

temperature.

Selecting 0

effectively

disables the

OSC function.

Available Start-up Periods

With a -2°C deviation and the 30 min. curve selected the

heating plant will switch on 15 min. before the Event 1 time.

Degrees below the desired

temperature at the beginning

of the Optimum Start Period

120 90 60 30 Event 1

min. min. min. min. time (0)

-1°C

-2°C

-3°C

-4°C

Thermostat Speci cation

Thermostat Features TP7000-RF TP7000 TP7000M

Order code - Built-in Sensor 087N741000 087N741400 087N740000 087N740400 087N740800 087N741900

- Remote Sensor

(A models)

087N741100 087N741500 087N740100 087N740500 087N740900 087N742000

Control type -

On/O or Chrono-proportional,

3/6 cycles per hour

•••

Control type -

On/O or Chrono-proportional,

6/12 cycles per hour (C models)

•••

RF - Wireless thermostat •

Hard wired thermostat • •

Digital clock type 24 hour (can be set to AM/PM mode by user)

Selectable 7-day or 5/2-day operation Yes

Number of events per day Up to 6

Control temperature range O , 5-30°C (can be set to Fahrenheit by user)

Total switching di erential

(On/O mode)

<1.0°C

Factory pre-set programme Yes

Programmable holiday mode Yes, up to 99 days

Installer selectable

optimum start control

Yes - O , 30, 60, 90 or 120 minutes early switch on at set-point minus 4K

Thermostat mode and frost mode Yes, set to 8.0°C, but adjustable between 5-30°C

Power supply 2 x AA/MN1500/LR6 alkaline batteries 230V, 50 Hz

Memory back-up Capacitor during battery change for 1 minute

Rechargeable cell

(see note 1)

Switching action of output relay N/A SPDT

Switch rating of relay contact,

voltage and current

N/A 3 (1) A, 10-230 Vac

Transmitter frequency (RF models only) 433.92 MHz N/A

Transmitter range (RF models only) 30 metres max. N/A

Dimensions (mm) 138 wide x 88 high x 28 deep

Pollution situation Degree 2

Rated impulse voltage N/A 2.5Kv

Ball pressure test 75°C

Note 1: Unit must be powered up for 6 days to charge cell before full back up is available

Receiver Speci cation

(RF Models Only)

Receiver Features RX1 RX2 RX3

Order codes 087N747600 087N747700 087N747800

Single channel receiver module,

works in conjunction with one thermostat

•

Two channel receiver module,

works in conjunction with two thermostats

•

Three channel receiver module,

works in conjunction with three thermostats

•

Transmitter code self learning feature • • •

Receiver frequencies 433.92 MHz

Supply voltage 220/240 Vac, 50 Hz

Output relay current rating 3 (1) A

Output relay con guration (commons linked internally) 1 x SPDT

1 x SPDT

1 x SPST

1 x SPDT

2 x SPST

Memory retention Memory retained electronically on power down

Dimensions (mm) 138 wide x 88 high x 32 deep

1 2 3 4

Komentáře k této Příručce

Žádné komentáře

Danfoss TP7000 Uživatelský manuál Strana 2

Komentáře k této Příručce

Související produkty a manuály pro Termostaty Danfoss TP7000