Danfoss FC 100 Series Specifikace stáhnout pdf (Strana 52)

Non UL compliance

If UL/cUL is not to be complied with, Danfoss recommends

using the fuses mentioned in the below table, which will

ensure compliance with IEC 61800-5-1:

In case of malfunction, not following the fuse recommen-

dation may result in damage to the frequency converter.

UL Non

Bussmann Bussmann Bussmann Bussmann Max.

Fuse

Power

Type RK5 Type RK1 Type J Type T Type

3 x 200-240V

0.25 FRS-R-10 KTN-R10 JKS-10 JJN-10 10

0.37 FRS-R-10 KTN-R10 JKS-10 JJN-10 10

0.75 FRS-R-10 KTN-R10 JKS-10 JJN-10 10

1.5 FRS-R-10 KTN-R10 JKS-10 JJN-10 10

2.2 FRS-R-15 KTN-R15 JKS-15 JJN-15 16

3.7 FRS-R-25 KTN-R25 JKS-25 JJN-25 25

5.5 FRS-R-50 KTN-R50 JKS-50 JJN-50 50

7.5 FRS-R-50 KTN-R50 JKS-50 JJN-50 50

11 FRS-R-80 KTN-R80 JKS-80 JJN-80 65

3 x 380-480V

0.37 FRS-R-10 KTS-R10 JKS-10 JJS-10 10

0.75 FRS-R-10 KTS-R10 JKS-10 JJS-10 10

1.5 FRS-R-10 KTS-R10 JKS-10 JJS-10 10

2.2 FRS-R-15 KTS-R15 JKS-15 JJS-15 16

3 FRS-R-15 KTS-R15 JKS-15 JJS-15 16

4 FRS-R-15 KTS-R15 JKS-15 JJS-15 16

5.5 FRS-R-25 KTS-R25 JKS-25 JJS-25 25

7.5 FRS-R-25 KTS-R25 JKS-25 JJS-25 25

11 FRS-R-50 KTS-R50 JKS-50 JJS-50 50

15 FRS-R-50 KTS-R50 JKS-50 JJS-50 50

18.5 FRS-R-80 KTS-R80 JKS-80 JJS-80 65

22 FRS-R-80 KTS-R80 JKS-80 JJS-80 65

30 FRS-R-80 KTS-R80 JKS-R80 JJS-R80 80

37 FRS-R-100 KTS-R100 JKS-R100 JJS-R100 100

45 FRS-R-125 KTS-R125 JKS-R125 JJS-R125 125

55 FRS-R-150 KTS-R150 JKS-R150 JJS-R150 150

75 FRS-R-200 KTS-R200 JKS-R200 JJS-R200 200

90 FRS-R-250 KTS-R250 JKS-R250 JJS-R250 250

5.2.5 EMC-Correct Electrical Installation

General points to be observed to ensure EMC-correct

electrical installation.

•

Use only screened/armoured motor cables and

screened/armoured control cables.

•

Connect the screen to earth at both ends.

•

Avoid installation with twisted screen ends

(pigtails), since this ruins the screening effect at

high frequencies. Use the cable clamps provide-

dinstead.

•

It is important to ensure good electrical contact

from the installation plate through the installation

screws to the metal cabinet of the frequency

converter.

•

Use starwashers and galvanically conductive

installation plates.

•

Do not use unscreened/unarmoured motor cables

in the installation cabinets.

How to Install VLT HVAC Basic Drive Design Guide

MG.18.C2.02 - VLT

is a registered Danfoss trademark 51

5 5

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 92 93

Komentáře k této Příručce

Žádné komentáře

Danfoss FC 100 Series Specifikace Strana 52

Komentáře k této Příručce

Související produkty a manuály pro Výkonové šroubováky Danfoss FC 100 Series